Planning for Quiet Operation
The NZXT Kraken Plus 240 is designed for efficient, low-noise cooling, but a few installation choices can make the difference between a whisper-quiet system and one that hums under load. This guide focuses on the steps that matter most for keeping noise low while maintaining strong CPU cooling performance.
The Kraken Plus 240 uses a custom NZXT Turbine pump engineered for high flow and head pressure. Its split-flow copper cold plate targets the CPU’s hottest areas for better heat transfer. While these features help with efficiency, proper mounting and fan orientation are key to minimizing audible noise.
Step 1: Choose the Right Radiator Position
Radiator placement affects both cooling and noise. For the quietest operation, mount the radiator at the top of your case as an exhaust. This allows warm air to rise naturally and keeps the pump at the lowest point in the loop — a standard best practice for AIO longevity.
If your case only supports front mounting, orient the radiator with the tubes at the bottom. This helps air bubbles collect at the top of the radiator rather than entering the pump, which can cause gurgling noises.
- Top exhaust mount: Best for quiet operation and overall system airflow. Warm air exits directly without recirculating through the case.
- Front intake mount: Acceptable if top mount isn't possible. Keep tubes at the bottom to reduce pump noise from trapped air.
Step 2: Install the Pump Block Correctly
The Kraken Plus 240 includes tool-free mounting brackets compatible with the latest AMD and Intel sockets, including AM5 and LGA 1851. Pre-applied thermal paste is already on the cold plate, so you don’t need to add extra.
Tighten the pump mounting screws evenly in a cross pattern to ensure the cold plate sits flat against the CPU. An uneven mount can create gaps that reduce heat transfer and cause the pump to work harder, increasing noise. The single breakout cable from the pump cap simplifies cable routing and reduces clutter.
Step 3: Set Fan and Pump Speeds via NZXT CAM
The Kraken Plus 240 comes with high-static pressure fans that move air efficiently through the radiator. By default, these fans can run at various speeds. For quiet operation, use NZXT CAM software to create a custom fan curve that keeps speeds low until CPU temperatures reach a threshold.
The pump itself is also controllable through NZXT CAM. Setting the pump to a fixed lower speed (e.g., following the product instructions) often reduces pump whine without sacrificing cooling performance. The LCD display can show real-time system temps, helping you monitor the impact of your adjustments.
Note: The supplied information does not specify exact pump speed percentages or RPM values. Use NZXT CAM to find the lowest pump speed that still keeps your CPU at safe temperatures under your typical workload.
Step 4: Leverage Zero RPM Mode for Near-Silent Idle
The Kraken Plus 240 supports Zero RPM Mode, which stops the fans completely when the CPU is at low load. This feature is ideal for quiet operation during everyday tasks like web browsing or document editing. When the CPU temperature rises during gaming or rendering, the fans spin up automatically.
Enable Zero RPM Mode in NZXT CAM. The fans will remain off until a temperature threshold is crossed, then gradually ramp up. This prevents unnecessary fan noise during light use while still providing full cooling when needed.
Final Checks for a Quiet Build
After installation, listen for any unusual sounds. A steady hum from the pump is normal, but gurgling or clicking may indicate trapped air. If you hear these, gently tilt the case to help air bubbles move to the radiator. Over time, most bubbles will settle in the radiator and noise will diminish.
The Kraken Plus 240's reinforced rubber tubing with nylon-braided sleeving is designed for durability and easy routing. Ensure tubes are not kinked or pinched, as this can restrict flow and cause the pump to strain, increasing noise.
Kraken Plus 240 Key Features for Quiet Cooling
- Kraken Plus 240: The NZXT Turbine pump is engineered for high flow and head pressure, delivering efficient, low-noise cooling. A pump designed for efficiency inherently produces less noise than a generic pump, making it a good foundation for a quiet build.

Kraken Plus 240 - Kraken Plus 240: Zero RPM Mode stops the fans completely at low loads for silent operation. This feature eliminates fan noise during idle or light tasks, directly contributing to quieter overall system operation.
- Kraken Plus 240: High-static pressure fans move air through the radiator to dissipate heat effectively. Effective airflow means fans can run at lower speeds while still maintaining good cooling, reducing noise.


